One-piece brake rotors for the front axle of the Audi RS6 (C7) and RS7 (2013-2018) without CCB

GIRODISC
Reference: GIRO-D1-190
Supplier Ref.: D1-190

Price: €1,322.50 Tax included
Available to order Within 10 days on average.
Unavailable in store (Montpellier)
Earn 1322 loyalty points (that is €65.00 in vouchers)

These Girodisc D1-190 alternative front brake pads (390 × 36 mm) allow you to replace the brake pads on Audi RS6 (C7) and RS7 models without carbon-ceramic rotors (2013–2018) while retaining the compatible brake rotors after inspection. These cast-iron pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without calipers.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the caliper housing and helps the rotor center itself between the pads, ensuring consistent contact even when hot.

New brake pads must be installed with new discs or rotors. Their shape and compound must match the mounting, cast iron type, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc D1-190 rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: D1-190
  • Position: front
  • Sizes (diameter × thickness): 390 × 36 mm
  • Vehicles and models: Audi RS6 (C7) and RS7 without carbon-ceramic brake disks (2013–2018)
  • Braking surface: cast iron
  • Packaging: pair of brake pads, one left and one right; rotors not included.
  • Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with OEM rotors.
  • Mounting hardware: New parts supplied with the kit; replace the entire track-to-cup mounting assembly during reassembly.
  • Part number for corresponding complete rotors: A1-190.
  • Internal ventilation: directional curved fins
  • Number of internal fins: 72
  • Minimum thickness: 34 mm
  • Original rotor diameter: 390 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number D1-190

Audi RS6 (C7) and RS7 without carbon-ceramic brake disks (2013–2018)

Compatibility and mounting requirements:

For stock cast-iron brake rotors, excluding carbon-ceramic rotors.

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake Pads and Brake System for Compatible Vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc D1-190 for compatible vehicles

What are the sizes of the D1-190 pads for my vehicle? The model shown measures 390 × 36 mm and is mounted on the front axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.

Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake drums are not included.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the D1-190 track and/or rotor and the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc D1-190 Alternative Tracks

  • 390 × 36 mm size for front braking on compatible vehicles.
  • Internal ventilation via curved fins to dissipate heat.
  • Alternative tracks to maintain a two-part mounting.
  • Left/right pair identified for mounting.
  • Compatible aluminum rotors are retained to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

  • Diameter in mm
    390
  • Position
    Front
  • Thickness
    36

16 other products in the same category: