One-piece brake rotors for Audi A4 (B6 and B7) (2000–2009) – S4 (B5, B6, and B7) (1997–2009) – A6 (C5) and allroad (1997–2004) –
Girodisc D1-309 alternative tracks for replacing brake rotors on Audi A4 (B6 and B7) models with Brembo 18Z conversion (2000–2009), Audi S4 (B5, B6, and B7) models with Brembo 18Z conversion (1997–2009), Audi A6 (C5) and allroad models with Brembo 18Z conversion (1997–2004), while retaining compatible rotors after inspection. These cast-iron brake pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without rotors.
The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the caliper housing and helps the rotor center itself between the brake pads, maintaining consistent contact when hot.
New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting configuration, cast material, and intended use; adhere to the specific requirements of this part number and perform the prescribed break-in procedure.
For use with the Brembo 18Z 6-piston caliper conversion. This part number is intended for a vehicle already equipped with this conversion; it does not replace the rotors on a standard Audi setup that retains its original calipers. Brembo calipers are not included. Confirm mounting brackets, clearances, and engine restrictions for the installation before ordering.
Specifications for Girodisc D1-309 rotors for compatible vehicles
- Brand: Girodisc
- PartNumber: D1-309
- Position: Front
- Vehicles and models: Audi A4 (B6 and B7) with Brembo 18Z calipers (2000–2009); Audi S4 (B5, B6, and B7) with Brembo 18Z calipers (1997–2009); Audi A6 (C5) and allroad with Brembo 18Z calipers (1997–2004)
- Braking surface: cast iron
- Packaging: pair of brake pads, one left and one right; rotors not included.
- Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with OEM rotors.
- Mounting hardware: Sport mounting kit included; replace the entire track/caliper mounting assembly during reassembly.
- Part number for corresponding complete rotors: A1-309.
- Internal ventilation: directional curved fins
- Mounting requirements: Vehicle must already be equipped with a Brembo 18Z 6-piston caliper conversion; calipers not included.
- Manufacturing of main components: United States
Vehicles compatible with Girodisc part number D1-309
Audi A4 (B6 and B7) with Brembo 18Z calipers (2000–2009)
Compatibility and Mounting Requirements:
For conversion with Brembo 18Z 6-piston front calipers; verify the exact vehicle configuration.
Only B5 S4 and C5 A6/Allroad models with 2.7-liter twin-turbo engines equipped with Brembo 18Z calipers. Models with 4.2-liter V8 engines are excluded. Do not order for any other A4/S4 model without technical validation.
Audi S4 (B5, B6, and B7) with Brembo 18Z calipers (1997–2009)
Compatibility and Mounting Requirements:
For conversion with Brembo 18Z 6-piston front calipers; verify the exact vehicle configuration.
Audi A6 (C5) and allroad with Brembo 18Z calipers (1997–2004)
Compatibility and Mounting Requirements:
For conversion with Brembo 18Z 6-piston front calipers; verify the exact vehicle configuration.
Each application is specific to its brake system version, calipers, and any requirements for brake pads or spacers. Verify these conditions before ordering.
Brake Pads and Brake System for Compatible Vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. Aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc D1-309 for compatible vehicles
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The discs are not included.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your intended use. Only S4 B5 and A6/Allroad C5 models with a 2.7-liter twin-turbo engine equipped with Brembo 18Z calipers. Models with a 4.2-liter V8 engine are excluded. Do not order for any other A4/S4 model without technical approval.
How do you identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal vanes, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build an even transfer ply. The PDF documents below detail the mounting and break-in process.
Is this part compatible with original Audi calipers? No. It is intended for a mounting that has already been converted to Brembo 18Z 6-piston calipers. The calipers are not included with the rotors. Check your vehicle’s actual configuration and the listed restrictions before ordering.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: one guide for installing and breaking in the rotors, and one guide for installing new pads on the existing calipers. Refer to the document that applies to your specific task before you begin.
Key Features of the Girodisc D1-309
- Internal ventilation via curved fins to dissipate heat.
- Alternative tracks to maintain a two-part mounting.
- Left/right pair identified for mounting.
- Compatible aluminum bowls are retained to maintain the benefits of the two-part mounting on unsprung and rotating masses.
-
PositionFront