One-piece brake rotors for the front of the Ferrari 360 Challenge Stradale (2003–2005) and the F430 (2004–2009) with CCB

GIRODISC
Reference: GIRO-D1-133
Supplier Ref.: D1-133

Price: €1,348.20 Tax included
Available to order Within 10 days on average.
Unavailable in store (Montpellier)
Earn 1348 loyalty points (that is €65.00 in vouchers)

These Girodisc D1-133 alternative front brake pads (380 × 34 mm) allow you to replace the brake pads on the Ferrari 360 Challenge Stradale (2003–2005) and the Ferrari F430 with carbon-ceramic rotors (2004–2009) while retaining the compatible brake rotors after inspection. These cast-iron pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without calipers.

The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the track and the caliper housing and helps the track center itself between the brake pads to maintain even contact when hot.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting configuration, cast material, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc D1-133 tracks for compatible vehicles

  • Brand: Girodisc
  • PartNumber: D1-133
  • Position: front
  • Sizes (diameter × thickness): 380 × 34 mm
  • Vehicles and models: Ferrari 360 Challenge Stradale (2003–2005); Ferrari F430 with carbon-ceramic rotors (2004–2009)
  • Braking surface material: cast iron
  • Packaging: pair of brake pads, one left and one right; brake rotors not included.
  • Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with original rotors.
  • Mounting hardware: new parts supplied with the kit; replace the entire disc-to-hub mounting assembly during reassembly.
  • Part number for corresponding complete rotors: A1-133.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 32 mm
  • Original rotor diameter: 380 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number D1-133

Ferrari 360 Challenge Stradale (2003–2005)

Compatibility and mounting requirements:

Brake pads with a maximum radial height of 66 mm are required for this track.

Ferrari F430 with carbon-ceramic rotors (2004–2009)

Compatibility and mounting requirements:

For vehicles with factory-installed carbon-ceramic brakes.

Brake pads with a maximum radial sweep height of 66 mm are required for this track.

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake pads and braking systems for compatible vehicles

For sports or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the shape of the brake pads remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc D1-133 for compatible vehicles

What are the sizes of the D1-133 pads for my vehicle? The part shown measures 380 × 34 mm and is mounted on the front axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.

Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake drums are not included.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your intended use. Brake pads with a maximum radial height of 66 mm are required for this braking surface.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and running in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc D1-133 Alternative Tracks

  • 380 × 34 mm size for front braking on compatible vehicles.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable alternative tracks to maintain a two-part mounting.
  • Left/right pair identified for mounting.
  • Compatible with existing aluminum brake rotors to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

  • Diameter in mm
    380
  • Position
    Front
  • Thickness
    34

16 other products in the same category: