The GT2i Race 6-point harness uses 100% polyester straps and can withstand forces of 3800 Newton.
The steel adjusters incorporate a spring to optimize tightening.
The yellow tabs allow you to loosen the straps quickly to untie yourself at the finish line.
This sedan harness also has a Velcro® strap for attaching a radio cable or water dropper.
The C40 steel aviation buckle meets the specifications and precise tolerances of the FIA standard. It receives C60 carbon steel fasteners.
Its central buckle has been redesigned to facilitate the locking and unlocking of the harness while reinforcing the mechanism to increase safety and at the same time prevent the entry of impurities inside the system.
PLEASE NOTE: Valid until December 31, 2031 for the .31 version!
Features :
Shoulder straps: 2"/3" HANS® specific
Abdominal straps: 3".
Aviation buckle on 6th point.
Made in Europe.
Delivered without eyelets
Certification FIA 8853-2016
MANUFACTURER: MCF S.R.L.
MODEL: 50100514
HOM. NO: SH.092.22-T-6
FIA STANDARD: 8853-2016
Our philosophy :
We wanted to adapt our seats to the evolution of the seating position over time. In the past, with cars not equipped with power steering and longer rallyes. Nowadays, with shorter stages, faster more direct input cars. When strength and stamina was needed, today's key words are speed, accuracy, comfort and adaptability. It was crucial to take into account every of these evolutions for the making of our seats range.
A fitting for various tilting options !
PLEASE NOTE: Valid until December 31, 2031 for the .31 version!
Tested by various body types, the GT2i Race-02 L V2 base was designed for a slightly more tilted driving position for increased comfort and safety in case of a potential crash. The driver is held in place, both at the thighs and shoulders while keeping a great freedom of movements for a quick steering input.
Their anatomic design allows for a wide variety of adjustments up to a more upright position for older vehicles thanks to the wide adjustments possibilities offered by our mounting frames (GT-FIX001).
Back padding is designed to match the drivers spine and offer perfect comfort. Padding can be either added in the lower back and bottom cushions to refine the driving position. Mesh cloth offers breathability for the backrest. 3 magnets are integrated to retain the harness straps on the sides and base of the seat.
Finally, the shell has been improved to make it easier to install the bucket in your vehicle.
Please note: This seat being a size L/XL, it may require a modification to your specific fittings (Sparco type) for mounting.
Features :
Injecte resin shell seat
L size seat
Certification FIA 8855-1999
MANUFACTURER: FLB
MODEL: RACE-02L
HOM. NO: CS.466.21
FIA STANDARD: 8855-1999
Side (center distance 290mm) mounting frames
Weight : 9,9 kg
Lumbar, base adjustments and thigh brackets by padding overlay.
Magnet to retain the harness.
Honeycomb mesh fabric.
Sold with 4 BTR screws + washers for the mounting.
GT2I RACE-L FIA Fiberglass Seat + Race Harness Package
Reference:
PACK-GT2I-RACE-L-HARNAIS-6PTS
This cockpit package combines a GT2i RACE-L FIA fiberglass seat and a GT2i Race 6-point harness, designed for a competition-oriented installation in a sedan, with a clear objective: driver retention, pelvic and shoulder stability, and compliance with the FIA approval requirements specified for each component.
The GT2i Race 6-point sedan harness is FIA 8853-2016 homologated. Its 6-point configuration distributes forces across the pelvis and crotch to minimize submersion during deceleration. The shoulder straps have a width of 2" or 3" (depending on the configuration), with steel adjusters and a pull-up type buckle, which is popular for its precise and repeatable tightening in competition.
The GT2i FIA Race-02L -V2 Fiber 2026 seat, size L, is FIA 8855-1999 approved (homologation number: CS,466,21). This is a side-mounted bucket seat with a fiberglass shell and no adjustable tilt, designed to prioritize overall rigidity and lateral support. The advertised weight is 9.9 kg, which helps keep the in-car mass down while maintaining a shell structure designed for motorsports use. By combining a side-mounted bucket seat with an FIA-approved 6-point harness, this package aims to provide a more locked-in driving position, improved driving precision, and reduced unwanted driver movement, particularly during cornering and braking.
