One-piece brake rotors for the front of the Ferrari 458 Challenge (2010–2016) – 488 Challenge (2015–2019) – 488 Challenge Evo (2
These Girodisc D1-183 alternative track brake rotors, measuring 398 × 38 mm , allow you to replace the brake rotors on the Ferrari 458 Challenge (2010–2016), Ferrari 488 Challenge (2015–2019), and Ferrari 488 Challenge Evo (2015–2019) while retaining compatible rotors after inspection. These cast-iron pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without rotors.
The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting limits stresses caused by thermal expansion differences between the track and the caliper housing and helps the track center itself between the pads to maintain consistent contact when hot.
New brake pads must be installed with new discs or rotors. Their shape and compound must match the mounting, cast iron type, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc D1-183 rotors for compatible vehicles
- Brand: Girodisc
- PartNumber: D1-183
- Position: front
- Sizes (diameter × thickness): 398 × 38 mm
- Vehicles and models: Ferrari 458 Challenge (2010–2016); Ferrari 488 Challenge (2015–2019); Ferrari 488 Challenge Evo (2015–2019)
- Braking surface: cast iron
- Packaging: pair of brake pads, one left and one right; rotors not included.
- Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with original rotors.
- Mounting hardware: new parts supplied with the kit; replace the entire rotor/hub mounting assembly during reassembly.
- Part number for corresponding complete rotors: A1-183.
- Internal ventilation: directional curved fins
- Number of internal fins: 72
- Minimum thickness: 36 mm
- Original rotor diameter: 398 mm
- Manufacturing of main components: United States
Vehicles compatible with Girodisc part number D1-183
Ferrari 458 Challenge (2010–2016)
Compatibility and mounting requirements:
Use D1405-shaped brake pads with a compound designed for cast-iron rotors. The original carbon-ceramic brake pads are not compatible.
Ferrari 488 Challenge (2015–2019)
Compatibility and mounting requirements:
Use D1405-shaped brake pads with a compound designed for cast-iron rotors. The original carbon-ceramic brake pads are not compatible.
Ferrari 488 Challenge Evo (2015–2019)
Compatibility and Mounting Requirements:
Use D1405-shaped brake pads with a compound designed for cast-iron rotors. The original carbon-ceramic brake pads are not compatible.
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake Pads and Brake Systems for Compatible Vehicles
For sports or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc D1-183 for compatible vehicles
What are the sizes of the D1-183 pads for my vehicle? The part shown measures 398 × 38 mm and is mounted on the front axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your intended use. Use D1405-shaped brake pads with a compound designed for cast iron rotors. The original carbon-ceramic brake pads are not compatible.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and running in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc D1-183 Alternative Tracks
- 398 × 38 mm size for front braking on compatible vehicles.
- Internal ventilation via curved fins to dissipate heat.
- Replaceable alternative tracks to maintain a two-part mounting.
- Left/right pair identified for mounting.
- Compatible aluminum rotors are retained to preserve the benefits of the two-piece mounting on unsprung and rotating masses.
-
Diameter in mm398
-
PositionFront
-
Thickness38