Girodisc Rear Brake Discs - Lamborghini Gallardo Super Trofeo (2011–2013)
Girodisc A2-168 rear brake discs improve thermal management during repeated braking on Lamborghini Gallardo Super Trofeo models (2011–2013). Their cast-iron pads and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate pad replacement when worn. Sold in pairs, with one left-side brake disc and one right-side brake disc.
These discs are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the compatible mounting calipers; any required spacers and brake pad specifications must be followed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc A2-168 rotors for compatible vehicles
- Brand: Girodisc
- PartNumber: A2-168
- Position: rear
- Vehicles and models: Lamborghini Gallardo Super Trofeo (2011–2013)
- Braking surface material: cast iron
- Packaging: Pair of complete rotors, one left and one right with disc bells.
- Hub: 6061-T6 aluminum
- Construction: two-piece floating mounting design
- Replacement part number for these discs: D2-168. Verify compatibility with the caliper generation before replacement.
- Internal ventilation: directional curved fins
- Diameter: 380 mm
- Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A2-168
Lamborghini Gallardo Super Trofeo (2011–2013)
Compatibility and mounting requirements:
Mounting using the supplied caliper spacers.
Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake pads and braking systems for compatible vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc A2-168 for compatible vehicles
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. Both discs are shipped with their disc bells.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new discs or new braking surfaces. Use a compound suitable for cast iron and your intended use. Perform mounting using the supplied caliper spacers.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A2-168 Two-Piece Brake Discs
- 6061-T6 aluminum bowl and floating mount to manage thermal stresses.
- Internal ventilation via curved fins to dissipate heat.
- Alternative tracks to maintain a two-part mounting.
- Left/right pair identified for mounting.
- Aluminum rotors help reduce unsprung and rotating masses compared to a comparable one-piece cast iron disc.
-
Diameter in mm380
-
PositionRear