Girodisc 380x32 Front Brake Discs - Ford Mustang GT500 (S197) (2013-2014)

GIRODISC
Reference: GIRO-A1-091
Supplier Ref.: A1-091

Price: €1,476.60 Tax included
Available to order Within 10 days on average.
Unavailable in store (Montpellier)
Earn 1476 loyalty points (that is €75.00 in vouchers)

Girodisc A1-091 front brake discs, measuring 380 × 32 mm, optimize consistent braking performance during spirited driving in the Ford Mustang GT500 (S197) (2013–2014). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stress and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.

These rotors are intended for the front axle of compatible vehicles in the configuration shown below. They retain the compatible caliper mounting; any required spacers and pad specifications must be followed.

The cast iron track and floating connection allow the disc to accommodate thermal expansion differences between its two parts and center itself between the brake pads. This construction also makes it easier to replace the tracks when they are worn.

The hub is made of 6061-T6 aluminum.

New pads must be installed with new discs or new tracks. Their shape and compound must match the mounting configuration, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A1-091 discs for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A1-091
  • Position: front
  • Sizes (diameter × thickness): 380 × 32 mm
  • Vehicles and models: Ford Mustang GT500 (S197) (2013–2014)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Housing: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Alternative track number for these rotors: D1-091. Verify compatibility with the caliper generation before replacement.
  • Minimum thickness: 29 mm
  • Overall height: 46 mm
  • Original rotor diameter: 380 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A1-091

Ford Mustang GT500 (S197) (2013–2014)

Compatibility and mounting requirements:

For 5.8-liter engine only.

Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake pads and brake systems for compatible vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the shape of the brake pads remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A1-091 for compatible vehicles

What are the sizes of the A1-091 discs for my vehicle? The model shown measures 380 × 32 mm and is mounted on the front axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their disc bells.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A1-091 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A1-091 Two-Piece Brake Discs

  • 380 × 32 mm size for front braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Alternative tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.

  • Diameter in mm
    380
  • Position
    Front
  • Thickness
    32

16 other products in the same category: