Girodisc 302x11 Rear Brake Discs - Ford Focus RS (2016-2018)
The Girodisc A2-169 rear brake discs, measuring 302 × 11 mm, optimize consistent braking performance during spirited driving in the Ford Focus RS (2016–2018). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stress and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.
These rear discs are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the calipers from the compatible mounting; any required spacers and pad specifications must be followed.
The cast iron track and floating connection allow the rotor to accommodate thermal expansion differences between its two parts and center itself between the brake pads. This construction also makes it easier to replace the tracks when they are worn.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-trimmed to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating assembly.
New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; adhere to the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc A2-169 rotors for compatible vehicles
- Brand: Girodisc
- PartNumber: A2-169
- Position: rear
- Sizes (diameter × thickness): 302 × 11 mm
- Vehicles and models: Ford Focus RS (2016–2018)
- Braking surface material: cast iron
- Packaging: Pair of complete rotors, one left and one right with disc bells.
- Housing: 6061-T6 aluminum
- Construction: two-piece floating mounting design
- Replacement part number for these rotors: D2-169. Verify compatibility with the caliper generation before replacement.
- Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A2-169
Ford Focus RS (2016–2018)
Compatibility and mounting requirements:
Third generation (Mk III).
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake pads and braking systems for compatible vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc A2-169 for compatible vehicles
What are the sizes of the A2-169 discs for my vehicle? The model shown measures 302 × 11 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their hubs.
Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A2-169 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the rotors, and an instruction manual for installing new tracks on existing rotors. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A2-169 Two-Piece Brake Discs
- 302 × 11 mm size for rear braking on compatible vehicles.
- 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
- Replaceable tracks to maintain a two-piece mounting.
- Left/right pair identified for mounting.
- Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.
-
Diameter in mm302
-
PositionRear
-
Thickness11