Girodisc 380x28 Rear Brake Discs for BMW M2 - M3 - M4 (F8X) (2014-2020)

The Girodisc A2-220 rear brake discs, measuring 380 × 28 mm, improve thermal management during repeated braking on the BMW M2, M3, and M4 (F8X) (2014–2020). Their cast-iron tracks and aluminum bowls form a floating assembly designed to manage thermal stresses and facilitate the replacement of tracks under wear. Sold in pairs, with one left and one right disc.

These rotors are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be observed.

The cast iron track and floating connection allow the disc to accommodate differences in thermal growth between its two parts and to center itself between the brake pads. This construction also makes it easier to replace the tracks when they are worn.

The hub is made of 6061-T6 aluminum.

New pads must be installed with new discs or new tracks. Their shape and compound must match the mounting configuration, the cast iron track, and the intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.

Specifications for Girodisc A2-220 discs for compatible vehicles

• Brand: Girodisc
• PartNumber: A2-220
• Position: rear
• Sizes (diameter × thickness): 380 × 28 mm
• Vehicles and models: BMW M2, M3, and M4 (F8X) (2014–2020)
• Braking surface: high-resistance cast steel
• Packaging: Pair of complete rotors, one left and one right with disc bells.
• Hub: 6061-T6 aluminum
• Construction: two-piece floating mounting design
• Catalog part number: D2-220. Verify compatibility with the caliper generation before replacement.
• Minimum thickness: 26 mm
• Original rotor diameter: 380 mm
• Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-220

• BMW M2, M3, and M4 (F8X) (2014–2020)

• BMW M2, M3, and M4 (F8X) (2014–2020): Red, silver, or gold calipers, including carbon-ceramic; 400 mm front disks.

Each application is subject to its specific brake configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.

Girodisc A2-220 Mounting Requirements

• BMW M2, M3, and M4 (F8X) (2014–2020): Red, silver, or gold calipers, including carbon-ceramic; 400 mm front disks.

Brake Pads and Brake System for Compatible Vehicles

Choose brake pads whose shape is compatible with the calipers, track, and/or the A2-220 rotor, and whose compound is suitable for sport driving or track use. The Endless, pagid Racing, or Ferodo Racing ranges may be considered after verifying the appropriate part number.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.

Maintenance of the Girodisc mounting on compatible vehicles

Replacing the pads alone helps keep the controlled rotors in good condition. Reusing a rotor for up to three pad replacements is subject to inspection of its condition, its mounting components, and the mounting instructions; this number does not constitute a guaranteed service life. Use a new mounting component each time you replace the pads.

FAQ — Girodisc A2-220 for Compatible Vehicles

What are the sizes of the A2-220 discs for my vehicle? The part number shown measures 380 × 28 mm and is mounted on the rear axle. The diameter alone is not sufficient: also check the brake system type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their hubs.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A2-220 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.

PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.

Key Features of Girodisc A2-220 Bowl Brake Discs

• 380 × 28 mm size for rear braking on compatible vehicles.
• 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
• Replaceable pads to maintain a two-piece mounting.
• Left/right pair identified for mounting.
• Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.