Girodisc 360x28 Rear Brake Discs - Lamborghini Huracan STO (2021-2024) with CCB

GIRODISC
Reference: GIRO-A2-302
Supplier Ref.: A2-302

Price: €2,561.50 Tax included
Available to order Within 10 days on average.
Unavailable in store (Montpellier)
Earn 2561 loyalty points (that is €135.00 in vouchers)

The Girodisc A2-302 rear brake discs, measuring 360 × 28 mm, optimize braking consistency during spirited driving on Lamborghini Huracan STO models equipped with carbon-ceramic rotors (2021–2024). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate rotor replacement due to wear. Sold as a pair, including one left-hand and one right-hand rotor.

These rear discs are intended for the rear axle of compatible vehicles in the configuration specified below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be observed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, cast iron, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.

On compatible vehicles originally equipped with carbon-ceramic rotors, this pair provides a conversion solution to high-quality cast-iron track rotors. It allows you to remove and store the expensive original carbon-ceramic rotors to preserve them during intensive use, while reusing compatible calipers. Use new brake pads suitable for cast iron and adhere to the pad shapes and any spacers specified by the part number. Replaceable brake pads reduce the cost of replacing braking surfaces in heavy-duty uses and offer a choice of linings to tailor bite and pedal reaction to the intended use.


Specifications for Girodisc A2-302 rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-302
  • Position: rear
  • Sizes (diameter × thickness): 360 × 28 mm
  • Vehicles and models: Lamborghini Huracan STO with carbon-ceramic rotors (2021–2024)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right, with disc bells.
  • Hub: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Replacement part number for these rotors: D2-302. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Number of internal fins: 48
  • Minimum thickness: 30 mm
  • Original rotor diameter: 355 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-302

Lamborghini Huracan STO with carbon-ceramic rotors (2021–2024)

Compatibility and mounting requirements:

For vehicles with factory-equipped carbon-ceramic brakes.

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake Pads and Brake System for Compatible Vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mounting components, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-302 for compatible vehicles

What are the sizes of the A2-302 discs for my vehicle? The model shown measures 360 × 28 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new brake pads. Their shape and compound must be compatible with the A2-302 rotor and/or braking surfaces and the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in the mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A2-302 Two-Piece Brake Discs

  • 360 × 28 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable brake pads to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum housings to control the unsprung mass and rotating mass of the conversion kit.

  • Diameter in mm
    360
  • Position
    Rear
  • Thickness
    28

16 other products in the same category: