MMX RP650 Fast road pad upgrade front | BMW F8x M-Cars
Reference:
MMR27-1001F
Supplier Ref.:
MMR27-1001F
If you drive your F-Series M-Car hard, the chances are you’ve experienced brake fade at some point. That’s where our high-performance RP650 brake pads come in. A simple replacement for your factory pads using the standard braking hardware, they deliver a much higher resistance to high temperature fade. This makes them perfect for fast road driving and even occasional track day use, yet without any compromise in daily driving.
Our compound testing focussed on developing a pad that finds that sweet-spot between excellent cold bite and high temperature fade resistance. The result is a medium aramid fibre compound with friction coefficient of 0.42mu in the temperature range of 450 – 650°C.
This compound is the secret to how our high-performance RP650 brake pads provide superior stopping power and reliable performance under even the most demanding conditions yet without requiring a warmup period - essential for cars that have to perform perfectly in daily driving duties yet stand up to the demands of fast road and occasional track use.
Finally, it’s a legal requirement in most countries for brake pads to carry ECE-R90 certification – yet many other aftermarket pads do not. Not only is this ECE-R90 standard essential for legality (and potentially your insurance validity), this regulation gives you the peace of mind that the pads are tested and approved for cold performance, speed, sensitivity, friction behaviour, compressibility, shear and hardness. So, the pads will work just as well when cold as when up to full track temperatures.
Perfect for fast road use.
Complete plug-and-play OE replacement.
Matching rear MMX pads available separately.
Matching 2-piece MMX discs available separately.
R90 Approved.
Excellent cold bite and high temperature fade resistance.
Suitable for short use track days.
Bedding in happens naturally over the first 100-200 miles in urban driving. See procedure in fitting information.
Quiet and smooth braking with shimmed, slotted, chamfered construction.
Responsive pedal feel for progressive braking.
Bedding in: After completing installation, make a series of 10 stops from 60mph (100kph) to 5-10mph (10-15kph). At the end of each stop, immediately accelerate back up to around 60mph (100kph) again for the next stop (the exact speed is not critical).
As you decrease to around 5-10 MPH (10-15kph), it is not necessary to watch the speedometer, keep your eyes on the road and approximate your speed at the end of each cycle. Do not come to a complete stop, as you will imprint pad material onto the disc, risking a vibration.
On the 8th or 9th stop, there should be a distinct smell from the brakes. Smoke may be evident after several stops as well. Also, by the 8th or 9th stop, some friction materials will experience “green fade”. This is a slight fading of the brakes. The fade will stabilise, but not completely go away until the brakes have cooled.
Our compound testing focussed on developing a pad that finds that sweet-spot between excellent cold bite and high temperature fade resistance. The result is a medium aramid fibre compound with friction coefficient of 0.42mu in the temperature range of 450 – 650°C.
This compound is the secret to how our high-performance RP650 brake pads provide superior stopping power and reliable performance under even the most demanding conditions yet without requiring a warmup period - essential for cars that have to perform perfectly in daily driving duties yet stand up to the demands of fast road and occasional track use.
Finally, it’s a legal requirement in most countries for brake pads to carry ECE-R90 certification – yet many other aftermarket pads do not. Not only is this ECE-R90 standard essential for legality (and potentially your insurance validity), this regulation gives you the peace of mind that the pads are tested and approved for cold performance, speed, sensitivity, friction behaviour, compressibility, shear and hardness. So, the pads will work just as well when cold as when up to full track temperatures.
Perfect for fast road use.
Complete plug-and-play OE replacement.
Matching rear MMX pads available separately.
Matching 2-piece MMX discs available separately.
R90 Approved.
Excellent cold bite and high temperature fade resistance.
Suitable for short use track days.
Bedding in happens naturally over the first 100-200 miles in urban driving. See procedure in fitting information.
Quiet and smooth braking with shimmed, slotted, chamfered construction.
Responsive pedal feel for progressive braking.
Bedding in: After completing installation, make a series of 10 stops from 60mph (100kph) to 5-10mph (10-15kph). At the end of each stop, immediately accelerate back up to around 60mph (100kph) again for the next stop (the exact speed is not critical).
As you decrease to around 5-10 MPH (10-15kph), it is not necessary to watch the speedometer, keep your eyes on the road and approximate your speed at the end of each cycle. Do not come to a complete stop, as you will imprint pad material onto the disc, risking a vibration.
On the 8th or 9th stop, there should be a distinct smell from the brakes. Smoke may be evident after several stops as well. Also, by the 8th or 9th stop, some friction materials will experience “green fade”. This is a slight fading of the brakes. The fade will stabilise, but not completely go away until the brakes have cooled.
