EVANS Coolant Oil Change Preparation 5L

EVANS hygroscopic preparatory liquid.

This liquid is made to clean all the cooling system to remove all the water present in the systems.
It can be use several times.
This Evans liquid prepares the cooling system to add the waterless coolant.

Capacity: 5L

Less detail

This EVANS waterless coolant is the fruit of many decades of research and development.

The engineers had specially designed this coolant to maintain the engines at the right temperature in the hardest weather conditions (freezing point below -40°C).

The life-long coolant :

As well as improving your cooling system, the EVANS coolant allows to improve your engine lifespan. This protection will be effective all the life-long of your engine without be changed!!

Waterless - No overheating

The EVANS coolant boiling point is above 180°C.

Waterless - No corrosion

Because it's waterless, the EVANS coolant prevents and eliminates corrosion.

Waterless - Low pressure

The EVANS coolant allows to reduce the pressure in the cooling system.

Waterless - No limescale

By preventing limescale accumulation, the EVANS coolant avoids the transfer of inefficient heat.

USE:

It's important to read carefully the instructions below for the EVANS coolant proper functionning:

1/ Remove the actual coolant present in your cooling system including the one in your heat unity.

2/ Fill the system with the EVANS hygroscopic preparation liquid (Ref: EV-PREP-FLUID). This liquid allows to aliminate all pieces of dirt, limescale debris and other residues that may affect the proper functionning of the EVANS coolant.

3/ Start the engine to its normal functionning temperature and then, allow to cool. Drain again the cooling system.

4/ Fill the cooling system with the EVANS waterless coolant. Run the engine to its normal functionning temperature to expel all the air present in the system.

5/ After the first use, you have to check the coolant liquid level and complete if necessary.

Capacity: 5L

Less detail

EVANS hygroscopic preparatory liquid.

This liquid is made to clean all the cooling system to remove all the water present in the systems.
It can be use several times.
This Evans liquid prepares the cooling system to add the waterless coolant.

Capacity: 5L

Less detail

This EVANS waterless coolant is the result of decades of research and development.

Engineers have specifically created CLASSIC COOL 180° for Historic Vehicles with engines made of cast iron blocks and copper, steel and aluminum components. This coolant keeps engines at the right temperature in the harshest conditions. (freezing point at -40°C)

* The coolant that lasts a lifetime:

In addition to improving your cooling system, EVANS coolant helps improve the life of your engine. This protection will be active all the life of the engine without being replaced!

No water - No overheating:

The boiling point of EVANS coolant is above 180°C.

Without water - Without corrosion

Without water, EVANS coolant helps prevent and eliminate corrosion.

Waterless - Pressureless

EVANS coolant reduces the pressure in the cooling system.

Waterless - Scale Free:

By preventing the build-up of hard scale, EVANS coolant prevents inefficient heat transfer.

Waterless - More Power:

Premature detonation associated with overheating is eliminated with this waterless coolant.

USE:

In order to ensure the performance of EVANS coolant, it is important to follow the guidelines below:

1/ Remove the coolant present in your cooling system, including the heater unit.

2/ Fill the circuit with EVANS hygroscopic preparation liquid (Ref: EV-PREP-FLUID). This fluid removes all dirt, scale debris and other residues which may impair the functioning of the EVANS coolant.

3/ Start the engine until it reaches normal operating temperature, then allow it to cool. Drain the cooling system again.

4/ Fill the cooling system with EVANS coolant without water. Run the engine until it reaches normal operating temperature to expel air from the system.

5/ After the first use, check the coolant level and top up if necessary.

Capacity : 5L

Less detail

EVANS hygroscopic preparatory liquid.

This liquid is made to clean all the cooling system to remove all the water present in the systems.
It can be use several times.
This Evans liquid prepares the cooling system to add the waterless coolant.

Capacity: 5L

Less detail

Vintage cool 180 ..... is for pre 1930 cars engines that contain, nodular pre-cast iron, carbon steel, copper and brass.

Less detail