# Girodisc 380x34 front brake discs for Porsche 911 (997) Turbo (2006–2012) with CCB—911 (991) Turbo and Turbo S (2013–2019) witho

> Pair of Girodisc front disks, 380 × 34 mm, part no.: A1-066. High-performance floating brake discs with aluminum hubs for the Porsche 911 (997) Turbo with CCB (2006–2012); Porsche 911 (991) Turbo and Turbo S without CCB (2013–2019); Porsche Cayman (981) GT4 without CCB (2015–2016); Porsche 718 (982) Cayman GT4 and Boxster Spyder without CCB (2019–2023).

- URL: https://www.gt2i.com/en/brake-disk-for-bell/224604-girodisc-380x34-front-brake-discs-for-porsche-911-997-turbo-20062012-with-ccb911-991-turbo-and-turbo-s-20132019-witho-3666618859293.html
- Reference: GIRO-A1-066
- Price: €2,247.00
- Brand: GIRODISC
- Availability: out of stock

## Description

Girodisc A1-066 front brake discs (380 × 34 mm) improve thermal management during repeated braking on Porsche 911 (997) Turbo models with carbon-ceramic rotors (2006–2012), Porsche 911 (991) Turbo and Turbo S without carbon-ceramic rotors (2013–2019), Porsche Cayman (981) GT4 without carbon-ceramic rotors (2015–2016), Porsche 718 (982) Cayman GT4 and Boxster Spyder without carbon-ceramic rotors (2019–2023). Their cast-iron tracks and aluminum bowls form a floating assembly designed to handle thermal stresses and facilitate the replacement of tracks that are worn. Sold in pairs, with one left-hand rotor and one right-hand rotor.
These rotors are intended for the front axle of compatible vehicles in the configuration listed below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be observed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, cast iron, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
On compatible vehicles originally equipped with carbon-ceramic rotors, this pair provides a conversion solution to high-quality cast-iron track rotors. It allows you to remove and store the expensive original carbon-ceramic rotors to preserve them during intensive use, while reusing compatible calipers. Use new brake pads suitable for cast iron and adhere to the pad shapes and any spacers specified by the part number. Replaceable brake pads reduce the cost of replacing braking surfaces in heavy-duty use and offer a choice of linings to tailor bite and pedal reaction to the intended use.
Specifications for Girodisc A1-066 rotors for compatible vehicles
Brand: Girodisc
PartNumber: A1-066
Position: front
Sizes (diameter × thickness): 380 × 34 mm
Vehicles and models: Porsche 911 (997) Turbo with carbon-ceramic rotors (2006–2012); Porsche 911 (991) Turbo and Turbo S without carbon-ceramic rotors (2013–2019); Porsche Cayman (981) GT4 without carbon-ceramic rotors (2015–2016); Porsche 718 (982) Cayman GT4, Boxster Spyder without carbon-ceramic rotors (2019–2023)
Braking surface: cast iron
Packaging: Pair of complete rotors, one left and one right, with disc bells.
Hub: 6061-T6 aluminum
Construction: two-piece floating mounting design
Replacement part number for these rotors: D1-066. Verify compatibility with the caliper generation before replacement.
Internal ventilation: directional curved fins
Number of internal fins: 72
Minimum thickness: 32 mm
Overall height: 69.3 mm
Original rotor diameter: 380 mm
Weight / weight reduction: Weight per complete disc: approximately 10.89 kg (24 lb).
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A1-066
Porsche 911 (997) Turbo with carbon-ceramic rotors (2006–2012)
Compatibility and mounting requirements:
For vehicles equipped with factory PCCB rotors.
Porsche 911 (991) Turbo and Turbo S without carbon-ceramic rotors (2013–2019)
Compatibility and mounting requirements:
Without PCCB.
Porsche Cayman (981) GT4 without carbon-ceramic rotors (2015–2016)
Compatibility and mounting requirements:
Without PCCB.
Porsche 718 (982) Cayman GT4, Boxster Spyder without carbon-ceramic brake disks (2019–2023)
Compatibility and mounting requirements:
Without PCCB.
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.
Brake Pads and Brake System for Compatible Vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc A1-066 for compatible vehicles
What are the sizes of the A1-066 discs for my vehicle? The model shown measures 380 × 34 mm and is mounted on the front axle. The diameter alone is not enough: also check the brake type and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their disc bells.
Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A1-066 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Girodisc A1-066 Highlights
380 × 34 mm size for front braking on compatible vehicles.
6061-T6 aluminum rotor and floating mount to manage thermal stresses.
Internal ventilation via curved fins to dissipate heat.
Replaceable tracks to maintain a two-piece mounting.
Left/right pair identified for mounting.
Aluminum housings to control the unsprung mass and rotating mass of the conversion kit.

## Features

- Product type: Brake disc on a Bol
- Diameter in mm: 380
- Position: Front
- Thickness: 34
