# Girodisc 380x34 Front Brake Discs - Audi RS4 (B7) (2006-2008)

> Pair of Girodisc front disks, 380 × 34 mm, part no.: A1-100. High-performance floating brake discs on an aluminum hub for the Audi RS4 (B7) (2006–2008).

- URL: https://www.gt2i.com/en/brake-disk-for-bell/224592-girodisc-380x34-front-brake-discs-audi-rs4-b7-2006-2008-3666618859170.html
- Reference: GIRO-A1-100
- Price: €1,861.80
- Brand: GIRODISC
- Availability: out of stock

## Description

The Girodisc A1-100 front brake discs, measuring 380 × 34 mm, optimize consistent braking performance during spirited driving in the Audi RS4 (B7) (2006–2008). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate the replacement of rotors under wear. Sold in pairs, with one left-hand and one right-hand rotor.
These rotors are intended for the front axle of compatible vehicles in the configuration specified below. They retain the calipers from the compatible mounting; any required spacers and brake pad specifications must be followed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc A1-100 rotors for compatible vehicles
Brand: Girodisc
PartNumber: A1-100
Position: front
Sizes (diameter × thickness): 380 × 34 mm
Vehicles and models: Audi RS4 (B7) (2006–2008)
Braking surface material: cast iron
Packaging: pair of complete rotors, one left and one right with disc bells.
Hub: 6061-T6 aluminum
Construction: two-piece floating mounting design
Replacement part number for these rotors: D1-100. Verify compatibility with the caliper generation before replacement.
Internal ventilation: directional curved fins
Minimum thickness: 32 mm
Overall height: 47 mm
Original rotor diameter: 365 mm
Weight / weight reduction: Comparison stated in the manufacturer’s data sheet: approximately 10.25 kg per disc versus 11.57 kg for the original, for a weight savings of 1.32 kg per disc (2.63 kg per pair).
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A1-100
Audi RS4 (B7) (2006–2008)
Compatibility and mounting requirements:
380 mm mounting with caliper spacers.
Mounting using the supplied caliper spacers.
Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake Pads and Brake Systems for Compatible Vehicles
For sports or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. Aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mounting components, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc A1-100 for compatible vehicles
What are the sizes of the A1-100 discs for my vehicle? The model shown measures 380 × 34 mm and is mounted on the front axle. The diameter alone is not enough: also check the brake type and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.
Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your use. Perform mounting using the supplied caliper spacers.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A1-100 Two-Piece Brake Discs
380 × 34 mm size for front braking on compatible vehicles.
6061-T6 aluminum rotor and floating mount to manage thermal stresses.
Internal ventilation via curved fins to dissipate heat.
Replaceable tracks to maintain a two-piece mounting.
Left/right pair identified for mounting.
Aluminum rotors help reduce unsprung and rotating masses compared to a comparable one-piece cast iron disc.

## Features

- Product type: Brake disc on a Bol
- Diameter in mm: 380
- Position: Front
- Thickness: 34
