# Girodisc 391.1x34 Front Brake Discs for Dodge Viper ACR (2016+) with CCB

> Pair of Girodisc front disks, 391.1 × 34 mm, part no.: A1-165. High-performance floating brake discs on an aluminum hub for the Dodge Viper ACR with CCB (2016+).

- URL: https://www.gt2i.com/en/brake-disk-for-bell/224564-girodisc-3911x34-front-brake-discs-for-dodge-viper-acr-2016-with-ccb-3666618858890.html
- Reference: GIRO-A1-165
- Price: €2,182.80
- Brand: GIRODISC
- Availability: out of stock

## Description

Girodisc A1-165 front brake discs, measuring 391.1 × 34 mm, optimize consistent braking performance during spirited driving on Dodge Viper ACRs equipped with carbon-ceramic rotors (2016+). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate rotor replacement due to wear. Sold in pairs, with one left-hand rotor and one right-hand rotor.
These rotors are intended for the front axle of compatible vehicles in the configuration shown below. They retain the calipers from the compatible mounting; any required spacers and brake pad specifications must be followed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-trimmed to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New pads must be installed with new rotors or brake tracks. Their shape and compound must match the mounting, cast iron, and intended use; adhere to the specific requirements of this part number and perform the prescribed break-in procedure.
On compatible vehicles originally equipped with carbon-ceramic rotors, this pair provides a conversion solution to high-quality cast-iron rotors. It allows you to remove and store the expensive original carbon-ceramic rotors to preserve them during heavy-duty use, while reusing compatible calipers. Use new brake pads suitable for cast iron and adhere to the pad shapes and any spacers specified by the part number. Replaceable brake pads reduce the cost of replacing braking surfaces in heavy-duty applications and offer a choice of trims to tailor bite and pedal reaction to the intended use.
Specifications for Girodisc A1-165 rotors for compatible vehicles
Brand: Girodisc
PartNumber: A1-165
Position: front
Sizes (diameter × thickness): 391.1 × 34 mm
Vehicles and models: Dodge Viper ACR with carbon-ceramic brake disks (2016+)
Braking surface material: high-resistance cast steel
Packaging: Pair of complete rotors, one left and one right with disc bells.
Hub: 6061-T6 aluminum
Construction: two-piece floating mounting design
Catalog part number: D1-165. Verify compatibility with the caliper generation before replacement.
Internal ventilation: directional curved fins
Minimum thickness: 32 mm
Original rotor diameter: 391.1 mm
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A1-165
Dodge Viper ACR with carbon-ceramic rotors (2016+)
Dodge Viper ACR with carbon-ceramic rotors (2016+): Fifth generation with factory-installed carbon-ceramic brakes.
Dodge Viper ACR with carbon-ceramic rotors (2016+): Brake pads with a maximum radial sweep height of 66 mm are required for this track. Shape 1405.
Each application is specific to its brake system, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.
Girodisc A1-165 Mounting Requirements
Dodge Viper ACR with carbon-ceramic rotors (2016+): Fifth generation with factory carbon-ceramic brakes.
Dodge Viper ACR with carbon-ceramic rotors (2016+): Brake pads with a maximum radial sweep height of 66 mm are required for this track. Shape 1405.
Brake Pads and Brake Systems for Compatible Vehicles
Choose brake pads whose shape is compatible with the calipers, the track, and/or the A1-165 rotor, and whose compound is suitable for sport driving or track use. The Endless, pagid Racing, or Ferodo Racing ranges may be considered after verifying the appropriate part number.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements a mounting that is compatible with the original hydraulic system.
Maintenance of the Girodisc mounting on compatible vehicles
Replacing the pads alone helps keep the controlled rotors in good condition. Reusing a rotor for up to three pad replacements is subject to inspection of its condition, its mounting components, and the mounting instructions; this number does not constitute a guaranteed service life. Use a new mounting component with each pad replacement.
FAQ — Girodisc A1-165 for Compatible Vehicles
What are the sizes of the A1-165 discs for my vehicle? The part number shown measures 391.1 × 34 mm and is mounted on the front axle. The diameter alone is not sufficient: also check the brake system type and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their mounting hubs.
Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your intended use. Brake pads with a maximum radial height of 66 mm are required for this braking surface. Shape 1405.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the rotors, and an instruction manual for installing new tracks on existing rotors. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A1-165 Bowl Brake Discs
391.1 × 34 mm size for front braking on compatible vehicles.
6061-T6 aluminum rotor and floating mount to manage thermal stresses.
Internal ventilation via curved fins to dissipate heat.
Replaceable pads to maintain a two-piece mounting.
Left/right pair identified for mounting.
Aluminum rotors to control the unsprung mass and rotating mass of the conversion kit.

## Features

- Product type: Brake disc on a Bol
- Diameter in mm: 391,1
- Position: Avant
- Thickness: 34