# Girodisc 356x28 Front Brake Discs - Toyota Yaris GR and Corolla GR (2020+)

> Pair of Girodisc front disks, 356 × 28 mm, part no.: A1-268. High-performance floating brake discs on an aluminum hub for the Toyota Yaris GR and Corolla GR (2020+).

- URL: https://www.gt2i.com/en/brake-disk-for-bell/224518-girodisc-356x28-front-brake-discs-toyota-yaris-gr-and-corolla-gr-2020-3666618858432.html
- Reference: GIRO-A1-268
- Price: €1,412.40
- Brand: GIRODISC
- Availability: out of stock

## Description

The Girodisc A1-268 front brake discs, measuring 356 × 28 mm, improve thermal management during repeated braking on the Toyota Yaris GR and Corolla GR (2020+). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stress and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.
These rotors are designed for the front axle of your Toyota Yaris GR and Corolla GR in the configuration shown below. They are compatible with the existing calipers; any required spacers and brake pad specifications must be followed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stress caused by thermal expansion differences between the brake pad and the rotor housing and helps the pad center itself between the brake pads, maintaining consistent contact even when hot.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, casting, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc A1-268 rotors for the Toyota Yaris GR and Corolla GR
Brand: Girodisc
PartNumber: A1-268
Position: front
Sizes (diameter × thickness): 356 × 28 mm
Vehicles and models: Toyota Yaris GR and Corolla GR (2020+)
Braking surface material: cast iron
Packaging: Pair of complete rotors, one left and one right with disc bells.
Housing: 6061-T6 aluminum
Construction: two-piece floating mounting design
Replacement part number for these rotors: D1-268. Verify compatibility with the caliper generation before replacement.
Internal ventilation: directional curved fins
Number of internal fins: 48
Minimum thickness: 26 mm
Original rotor diameter: 356 mm
Manufacturing location of main components: United States
Vehicles compatible with Girodisc part number A1-268
Toyota Yaris GR and Corolla GR (2020+)
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.
Brake Pads and Brake System for Your Toyota Yaris GR and Corolla GR
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing you to retain the vehicle’s brake calipers. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement Brake Pads for Toyota Yaris GR and Corolla GR Girodisc Rotors
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc A1-268 for Toyota Yaris GR and Corolla GR
What are the sizes of the A1-268 discs for my Toyota Yaris GR and Corolla GR? The part number listed measures 356 × 28 mm and is designed for the front axle. The diameter alone is not sufficient: also verify the brake system version and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.
Do I need to replace the brake pads on my Toyota Yaris GR and Corolla GR?Yes. Always install new brake pads with new rotors or new brake pads. Their shape and compound must be compatible with the A1-268 rotor and/or braking surfaces and the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my Toyota Yaris GR and Corolla GR? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build an even wear ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We’ve included two PDF documents below: one manual for installing and breaking in the rotors, and one manual for installing new brake pads on existing rotors. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A1-268 Two-Piece Brake Discs
356 × 28 mm size for the front brakes of your Toyota Yaris GR and Corolla GR.
6061-T6 aluminum rotor and floating mount to manage thermal stresses.
Internal ventilation via curved fins to dissipate heat.
Alternative tracks to maintain a two-piece mounting.
Left/right pair identified for mounting.
Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast-iron disc.

## Features

- Product type: Brake disc on a Bol
- Diameter in mm: 356
- Position: Front
- Thickness: 28
